How to Use a Meat Thermometer: Probe Placement and Temps
How to use a meat thermometer: probe the thickest part, away from bone and fat, and read the temp against USDA minimums. Includes doneness, carryover and types.

As an Amazon Associate, ProteinPan earns from qualifying purchases. We never accept free products or payment for placement.
The short answer
- Probe the thickest part of the meat, with the sensor tip in the center and away from bone, fat and the pan.
- USDA safe minimums: 165°F for poultry, 160°F for ground meat, 145°F plus a 3-minute rest for whole cuts of beef, pork and lamb.
- Pull a little early. Thick cuts keep rising roughly 5-10°F as they rest, a common rule of thumb called carryover cooking.
- Pick the tool for the job: instant-read for quick checks, leave-in or wireless for roasts and long smokes.
On this page
Here is how to use a meat thermometer: push the probe into the thickest part of the meat, keep the tip in the center and away from bone, and wait for the reading to settle before you compare it with your target. The same habits apply whether you cook on a grill, in an oven or in a smoker, and they matter more once you move to the best wireless meat thermometer for monitoring from a distance. Below is the full routine, with temperatures.
How do you use a meat thermometer?
Check the meat near the end of the estimated cook time, not at the start. Insert the probe sideways or from the top into the thickest part, push until the sensor tip sits in the center, and wait a few seconds until the number stops moving. Then pull the probe and clean it before the next check.
- Start checking about 10 to 15 minutes before you expect the meat to be done.
- Insert the probe into the thickest part, tip in the center.
- Wait until the reading stops changing, usually a few seconds for a digital model.
- Check a second spot on large cuts, and trust the lowest number.
- Wipe the probe with hot soapy water between checks, especially when you move from raw to cooked food.

Where do you put the probe?
Put it in the thickest part of the meat, where heat arrives last. The sensor sits in the last inch or so of most probes, so the tip has to end up in the center of that thick part. Bone conducts heat and fat runs at a different temperature, so keep the tip off both.
How to use a meat thermometer when cooking steak
Slide the probe in from the side of the steak so the tip lands in the middle of the thickest section, not through the top and out the bottom. For thin steaks, a sideways entry is the only way to get the sensor surrounded by meat. Pull the steak when the reading is a few degrees under your target.
Poultry, roasts and ground meat
Each cut gets its own probe spot for an accurate internal temperature:
- Whole chicken or turkey: the thickest part of the breast and the innermost part of the thigh, without touching bone.
- Roast: the center of the thickest section.
- Burgers and meatballs: through the side, so the tip sits in the middle of the patty.
Thin cuts need a sideways entry
When a cut is under an inch thick, go in horizontally. A tip poking through the bottom reads the hot pan instead of the meat.
What is the difference between instant-read, leave-in and wireless?
An instant-read thermometer gives a reading in a few seconds and is for spot checks. A leave-in probe stays in the meat while it cooks and shows the temperature on a display outside the oven. A wireless thermometer sends that reading to a base or phone, so you can monitor a long cook without opening the lid.
| Type | Best for | Catch |
|---|---|---|
| Instant-read | Steaks, chops | Lid opens |
| Leave-in | Roasts, turkey | Wired display |
| Wireless | Long smokes | Needs charging |
For steaks and burgers, an instant-read thermometer is plenty. For a roast or a long smoke, a leave-in or wireless meat thermometer saves you from opening the lid again and again, which lets heat escape. Digital models read faster than dial types, and many digital probes list a response time in seconds.
What temperature is safe to eat?
The USDA publishes safe minimum internal temperatures: 165°F for poultry and leftovers, 160°F for ground beef, pork and other ground meats, and 145°F for whole cuts of beef, pork, veal and lamb followed by a 3-minute rest. Fish is also 145°F by the same USDA guidance. These are safety minimums, not taste targets.
| Food | USDA minimum | Rest |
|---|---|---|
| Poultry | 165°F | None |
| Ground meat | 160°F | None |
| Beef, pork, lamb | 145°F | 3 min |
| Fish | 145°F | None |
What doneness temperatures do cooks use for steak?
Doneness is a matter of taste, separate from the USDA minimums. Common cooking guidance for beef steaks puts rare around 120-125°F, medium-rare around 130-135°F, medium around 140-145°F and medium-well around 150-155°F. Only the last two meet or approach the USDA 145°F line, so choose with that in mind.
USDA safe: 145°F
Doneness ranges are common cooking guidance; 145°F is the USDA safe minimum for whole cuts of beef.
Doneness is not the safety line
Medium-rare is a texture preference. If you cook to a lower temperature than the USDA minimum, you are choosing a risk, and ground meat and poultry should always reach their minimums.

What is carryover cooking?
Carryover cooking is the temperature rise that continues after meat leaves the heat, because the hot outside keeps pushing heat toward the center. Large roasts and thick steaks commonly climb roughly 5-10°F while resting; thin cuts rise less. That is why many cooks pull the meat a few degrees below the final target.
To use it, subtract a few degrees from your goal, let the meat rest, and probe again before slicing. The USDA’s 3-minute rest for whole cuts overlaps with this rise.
How do you read a dial meat thermometer?
Read the needle at eye level against the printed numbers, not the doneness words printed on some dials. Many dial models show labeled zones such as beef or poultry, but the number is what you want. Dials also need the sensing area, often a dimple on the stem, fully inside the meat.
Can you take your temperature with a meat thermometer?
No. A food thermometer is built for cooking ranges and is not a medical device, so use a thermometer made for body temperature instead.
How often should you calibrate a meat thermometer?
Check it now and then, and after a drop. The simplest test is a glass of ice water: a good probe reads about 32°F once the water and ice settle. Boiling water reads about 212°F at sea level, lower at altitude. If yours is off, many digital models can be adjusted, or you can simply note the offset.
Quick reference before you cook
Using a meat thermometer well comes down to three habits: keep the probe in the center of the thickest part, check a second spot, and compare the internal temperature with the USDA minimum for what you are cooking. For long cooks, a wireless probe tracks the climb without opening the lid, so you never have to guess.
Next in this series: Meat Thermometer Chicken Temp: Where to Probe and 165°F
Frequently asked questions
What temperature is chicken done?
The USDA safe minimum internal temperature for poultry is 165°F, measured in the thickest part of the breast and the innermost part of the thigh, without touching bone.
Should the thermometer touch the bone?
No. Bone conducts heat differently and can give a false reading, so keep the probe tip in the center of the meat, away from bone, fat and the pan.
Do you leave a meat thermometer in while cooking?
Only if it is a leave-in or wireless probe made for it. Instant-read thermometers are for quick checks and should come out after the reading, since most are not built to sit in an oven or grill.